Michele Damoiseau(deleted)
|
netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
01/06/2011 10:35 AM
post81347
|
netinfo gives ERROR : "tx of raw data failed"
Hello,
I'm using a AT4NM10-I (ATOM D410) with 1 realtek RTL8112L network controller.
I'm using "Net.rtl8169" and "Net" very last version.
However, sometimes, the network access does not work. When this happens, I can see in the "netinfo" and "traceinfo" the
following message :
NET(tx) tx of raw data failed
Does anyone know what could be the problem?
Best regards
Michele
|
|
|
Oleg Bolshakov
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Oleg Bolshakov
01/12/2011 3:35 AM
post81970
|
Re: netinfo gives ERROR : "tx of raw data failed"
Hi Michele,
Did you get any messages from the Net.rtl8169 driver? Please, post here
output of the netinfo.
--
Respectfully,
Oleg
> Hello,
>
> I'm using a AT4NM10-I (ATOM D410) with 1 realtek RTL8112L network
> controller.
>
> I'm using "Net.rtl8169" and "Net" very last version.
>
> However, sometimes, the network access does not work. When this
> happens, I can see in the "netinfo" and "traceinfo" the following
> message :
>
> NET(tx) tx of raw data failed
>
> Does anyone know what could be the problem?
>
> Best regards
> Michele
>
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post81347
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
01/12/2011 4:40 AM
post81973
|
Re: netinfo gives ERROR : "tx of raw data failed"
Dear Oleg,
No, I don't have any messages from the Net.rtl8169. The only message coming in netinfo is :
NET(tx) tx of raw data failed.
Another information : as said before, the problem does not occure at each startup. When the startup works correctly and
that I have the IP connectivity (so no message in netinfo), then if I remove the ethernet link and I do a ping, the same
message appears too.
Many thanks
Regards
Michele
|
|
|
Oleg Bolshakov
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Oleg Bolshakov
01/14/2011 6:55 AM
post82290
|
Re: netinfo gives ERROR : "tx of raw data failed"
Hi Michele,
It seems that there is a problem with cables or something similar. Have
you tried to use several different patch-cords? Can you try cross-cable and
test how the driver works in point-to-point mode without switch?
--
Respectfully,
Oleg
> Dear Oleg,
>
> No, I don't have any messages from the Net.rtl8169. The only message
> coming in netinfo is :
>
> NET(tx) tx of raw data failed.
>
> Another information : as said before, the problem does not occure at
> each startup. When the startup works correctly and that I have the IP
> connectivity (so no message in netinfo), then if I remove the ethernet
> link and I do a ping, the same message appears too.
>
> Many thanks
>
> Regards
> Michele
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post81973
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
02/01/2011 9:17 AM
post82820
|
Re: netinfo gives ERROR : "tx of raw data failed"
Hi Oleg,
I have tried with a cross cable, I have exactly the same behaviour!
Regards
Michele
|
|
|
Oleg Bolshakov
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Oleg Bolshakov
02/04/2011 5:36 AM
post82893
|
Re: netinfo gives ERROR : "tx of raw data failed"
Hi Michele,
How you start the Net and the Net.rtl8169 driver?
--
Respectfully,
Oleg
> Hi Oleg,
>
> I have tried with a cross cable, I have exactly the same behaviour!
>
> Regards
> Michele
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post82820
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
02/04/2011 5:49 AM
post82894
|
Re: netinfo gives ERROR : "tx of raw data failed"
Dear Oleg,
Here is how I start them :
Net &
Net.rtl8169 -V10ech -d8168 -I0 -l2 &
Regards
Michele
|
|
|
Oleg Bolshakov
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Oleg Bolshakov
02/04/2011 9:22 AM
post82900
|
Re: netinfo gives ERROR : "tx of raw data failed"
Michele,
Do you really need to specify PCI IDs and index? Please, check how the
driver works with forced speed/duplex. Try to launch the driver with
different combinations of options -s, -F, e.g.:
Net.rtl8169 -s100 -F &
Is FLEET network working when TCP/IP fails?
--
Respectfully,
Oleg
> Dear Oleg,
>
> Here is how I start them :
>
> Net &
> Net.rtl8169 -V10ech -d8168 -I0 -l2 &
>
> Regards
> Michele
>
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post82894
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
02/04/2011 9:53 AM
post82904
|
Re: netinfo gives ERROR : "tx of raw data failed"
Dear Oleg,
I've tried all combinations of
Net.rtl8169 -s100 -F &
Net.rtl8169 -s100 &
Net.rtl8169 -F &
with and without specifying pci ID...
I'm not familiar with FLEET. Could you tell me how I can check FLEET network is working?
Many thanks
Regards
Michele
|
|
|
Oleg Bolshakov
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Oleg Bolshakov
02/09/2011 4:40 AM
post83017
|
Re: netinfo gives ERROR : "tx of raw data failed"
Hi Michele,
Does this issue occur with all combination of options? Also note that you
have to test the driver with -s10 and -s1000 too.
FLEET is a native QNX4 network protocol. Please, read how to configure
FLEET:
http://www.qnx.com/developers/qnx4/qnx4kb/solution.html?code=10203
--
Respectfully,
Oleg
> Dear Oleg,
>
> I've tried all combinations of
> Net.rtl8169 -s100 -F &
> Net.rtl8169 -s100 &
> Net.rtl8169 -F &
>
> with and without specifying pci ID...
>
> I'm not familiar with FLEET. Could you tell me how I can check FLEET
> network is working?
>
> Many thanks
>
> Regards
> Michele
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post82904
|
|
|
Hugh Brown
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Hugh Brown
02/09/2011 10:35 AM
post83031
|
Re: netinfo gives ERROR : "tx of raw data failed"
Is it possible for you to send us your hardware, so that we can rectify this problem?
Thanks, Hugh.
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
02/09/2011 10:54 AM
post83036
|
Re: netinfo gives ERROR : "tx of raw data failed"
Dear Hugh,
What do you mean by sending you my hardware?
Do you need the reference of motherboard and ethernet chip, or do you need
us to send you one motherboard?
As said in my first mail, I'm using a AT4NM10-I (ATOM D410) with 1 realtek
RTL8112L network controller.
Please let me know.
Many thanks
Kind regards
Michele
----- Original Message -----
From: "Hugh Brown" <community-noreply@qnx.com>
To: "general-qnx4" <post83031@community.qnx.com>
Sent: Wednesday, February 09, 2011 4:35 PM
Subject: Re: netinfo gives ERROR : "tx of raw data failed"
> Is it possible for you to send us your hardware, so that we can rectify
> this problem?
>
> Thanks, Hugh.
>
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post83031
>
|
|
|
Hugh Brown
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Hugh Brown
02/09/2011 4:00 PM
post83058
|
Re: netinfo gives ERROR : "tx of raw data failed"
Yes, if you could send us one motherboard it would help, as the problem could be specific to this motherboard and PHY.
Hugh.
|
|
|
Michele Damoiseau(deleted)
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Michele Damoiseau(deleted)
02/10/2011 4:50 AM
post83066
|
Re: netinfo gives ERROR : "tx of raw data failed"
I will try to organize that. Could you give me address and contact name to
send it?
Thank you
Regards
Michele
----- Original Message -----
From: "Hugh Brown" <community-noreply@qnx.com>
To: "general-qnx4" <post83058@community.qnx.com>
Sent: Wednesday, February 09, 2011 10:00 PM
Subject: Re: netinfo gives ERROR : "tx of raw data failed"
> Yes, if you could send us one motherboard it would help, as the problem
> could be specific to this motherboard and PHY.
>
> Hugh.
>
>
>
>
> _______________________________________________
>
> General
> http://community.qnx.com/sf/go/post83058
>
|
|
|
Hugh Brown
|
Re: netinfo gives ERROR : "tx of raw data failed"
|
Hugh Brown
02/10/2011 10:09 AM
post83081
|
Re: netinfo gives ERROR : "tx of raw data failed"
That would be great. Please send it to:
Hugh Brown,
QNX Software Systems
175 Terence Matthews Crescent,
Ottawa. ON. Canada.
K2M 1W8.
|
|
|
|